真空泵 / EJ-BA
EJ-BA-MEDIUMX2
• 非常适合分散应用
• 吸气流速和压缩空气消耗量之间的比率高
• 可以集成在夹持点附近,质量轻
• G3/8' 真空端口
• 辅助真空端口,用于 G1/8' 系统的可能吹扫或监控
• 提供双级和三级 EJ-MEDIUM 盒(EJ-LP、EJ-HF 和 EJ-HV)
应用示例
典型应用
• 搬运密封件,如玻璃和金属部件 (EJ-HV)
• 包装(装箱机、纸箱包装机)(EJ-HF、EJ-LP)
• 塑料(模塑)
• 自动、
夹具订制
AGG可在机械手和模具间提供精i准的中心。
注塑模具内金属嵌件安放时尤其要注意这一点。
夹具AGG...B 安装在EOAT上,钢管 AGG...C 安装在模具上。
一旦机械手向模具靠近,夹具在压力的作用下逐步向钢管靠近,
并与之接触。
AGG21-B 和 AGG30-B 采用的是双动作安全弹簧,确保在压缩空
气 (NC)缺失时设备的正常运行。
AGG19-B 采用的是单动作复位弹簧(NO)。
Gripper for engagement
The AGG is used to provide a precise centering between the robot
and the mould.
This necessary when metal inserts must be p1aced in the
mould, before the p1astic injection.
The gripper AGG…-B is fitted on the EOAT, while the steel bushing
AGG…-C is fitted on the mould.
Once the robot has approached the mould, the gripper is
pressurized, thus it closes and engages the bushing.
AGG21-B and AGG30-B are double-acting with a safety spring to
keep the gripper engaged even without compressed air (NC).
AGG19-B is single-acting with reset spring (NO).
ID 膨胀抓持器系列
• 创新性气动操作手新理念。
• 向下移动 (MFD) 或向上移动 (MFU)。
• 弹性部件可以是硅氧烷或 EPDM。
• 抓手直径为 8 至 85 毫米。
• 可选鼻形锥体用于对中。
• 可选接近磁性传感器。
• 配有几个安装附件。
ID expansion grippers series
• New concept for innovative air hands.
• Downward movement (MFD), or upward movement (MFU).
• The elastic part can be in Silicone or EPDM.
• Grip diameters from 8 to 85 mm.
• Optional nose cones for centering.
• Optional proximity magnetic sensors.
• Several mounting accessories.
传感器
可以通过一个 3 输出可编程传感器(需另行购买)检查运行位置,该传感器用于检测嵌入右侧颚形钳的磁体位置。
The operating position can be checked by one 3 - outputs programmable sensor (not included), detecting the position of the magnet on the right jaw.
以上信息由专业从事小型气动夹爪的吉玛泰克于2024/4/17 10:41:18发布
转载请注明来源:http://szhou.mf1288.com/jmtkzdh-2737049683.html